DIY PROJECTS

Traditional Tansu, Part 1: The case

Traditional Tansu, Part 1: The case

Tansu has long fascinated me. A tansu in an antique shop window contributed greatly to my taking up serious woodworking. Something about all of those drawers and doors spoke to me, not only of function but of potential. Like the pages of a brand new sketchbook, it’s not the empty drawers that make a tansu compelling, but what you might fill them with.

The particular tansu that inspired this build is called a ko-dansu, or personal storage chest. What all of the drawers were intended for I have no idea, but the proportions and layout appealed to me. While the original was built from kiri (paulownia), I’ll be building this one from Port Orford Cedar. Enough talk, let’s build a tansu!

Finger joints

The carcasses of box-style tansu like this one (as opposed to frame-and-panel style) are commonly constructed using wide, pinned finger joints, and almost always have five fingers per corner. The fingers are typically cut in opposition at the top and bottom corners, and because keeping track can get confusing, it’s important to mark which fingers will be removed and which will stay.

I lay out all of the fingers with a square. The case sides are 1⁄2 in. thick, but because I want a little overhang to plane off later, I make the fingers 9⁄16 in. deep. At the table saw, I carefully set up stops and made cheek cuts for both ends of the top piece and the bottom ends of the side pieces.

Before cutting the cheeks for the mating fingers, I use an offcut the same width as the case pieces to reset the stops. To make shoulder cuts at the edges of the boards, I use a miter gauge at the table saw; for the shoulders between fingers, I use the bandsaw followed by hand chiseling.

When all of the joints are cut, I dry-fit the four sides and double-check the inside dimensions. I also make reference marks showing the location of the dadoes that house the back panel. These help keep track of inside/outside, front, and back on all four parts.

A piece of wood held on end being notched at the table saw.
Symmetrical slots. At the table saw, having set a stop block guided by his layout, Cullum uses a miter gauge to make the initial finger cut on one of the two-fingered joints. To cut the mirroring slot, he’ll next rotate the workpiece so the opposite edge is against the stop block.
Another notch is added to the same piece of wood.
 The central issue. After resetting the stop block, Cullum makes the two center kerfs.
A smaller piece is being notched at the table saw.
 Make it fit like a glove. Cullum uses a cutoff from one of the case boards to find the stopblock setting for cutting the central finger on the three-fingered side of the joint.
The two notched pieces of wood are being put together to check their fit.
 Then, having removed waste from the center gap in the two-fingered board, he tests the fit.
A larger piece is now being notched by the author.
 Slotting the case side. With the stop block’s new setting, Cullum cuts the slots on both sides of the central finger.
Now the piece is turned on end and being cut so a section of the board is being removed.
 Open shoulders. On the two-fingered joints, where the shoulders are accessible, Cullum cuts them at the table saw with the workpiece on edge.
The area between the finger joints are being removed at the bandsaw.

For shoulders that can’t be table-sawn, rough out the waste at the bandsaw.

The author uses a chisel to slice more of the wood away.

Then pare to the baseline with a wide chisel and a 90° guide block.

The four pieces of wood are being fit together by the author.
Interlace the case. With the finger joints complete, Cullum tests their fit.

Tongues and tenons

The interior case parts are all joined with a Japanese variation on the tongue-and-groove. A continuous tongue is cut first. Then a notch is cut through the tongue creating a 3⁄4-in.-wide tenon that helps with assembly and keeps the parts from drifting over time.

Using a scrap piece and the dado stack on the table saw, I dial in cuts to create a tongue that is 1⁄4 in. long and 1⁄4 in. wide. I cut tongues on the ends of all of the internal parts, and then modify the tongues by cutting a 1⁄2-in.-deep front shoulder and then the notch that creates the separated tenon at the front. Once all the parts are cut at the table saw, I finish the notch with a chisel.

I use my trim router with a 1⁄4-in. bit to make all of the dadoes and mortises for these joints. Because I prefer to chisel my dadoes and mortises square instead of rounding the tenons, I stop a little shy of the lines and finish up with a chisel.

The author pushes a piece of wood over the table saw.
Tongues to start with. The interior joinery begins with all the dividers in the case getting tongues cut on their ends. The long horizontal dividers also get tongued along their back edges.
A piece of wood is held on end again and pushed over the blade using a sled.
 Tongues become tenons. A notch cut through the tongue creates a separate tenon at the front of the joint. This aids in accurate assembly and keeps parts from drifting over time.
The author uses a router to excavate a groove.
 Grooving jig. Cullum’s routing box provides a square fence for his trim router to ride along as he cuts grooves for the short horizontal dividers. He routs to his end lines by eye and lifts and plunges again to cut the in-line mortise at the end of the groove.
The author chisels at the end of the previous groove
 Squaring up. After chopping the ends of the grooves and mortises square with chisels, Cullum tests the fit.

A piece of wood is inserted into the groove.

To the back

Here I depart from typical tansu construction. Traditionally, the back panel of a tansu is fitted beneath the top and nailed directly to the back edges of the carcass. This causes some wood movement issues, and it’s not attractive. Since this tansu will likely be seen from all sides, I chose to cut a tongue around the back and let it into the case.

Next, I dry-assemble the carcass with the back in place. Then I transfer to the back the location of the dadoes in the sides for the long horizontal dividers. Using those marks and a 1⁄4-in. dado stack, I cut dadoes across the back for the horizontal dividers.

Before moving on to make the sliding doors, I cut the tracks for them in the case top and bottom. At the table, I use a dado stack and the stop-and-drop method to cut them. I cut the tracks just slightly short, and then I fit the vertical divider into place, mark the track ends with a knife, and finish up with a chisel.

The author reaches into the piece with a pencil marking the location of the groove.
Fit and mark. Having grooved the case parts for the back and rabbeted the back to create a tongue to fit the grooves, Cullum dry fits the carcass. Then he transfers the groove locations for the two long horizontal dividers onto the back.
The author feed the piece over the table saw
 Grooving the back. Using the marks he just made, Cullum cuts grooves in the back to accept the long horizontal dividers. Locking them into the back makes the case rigid and keeps the long dividers from deflecting.
The author carefully lowers a piece on the table saw
 Careful tracking. Cullum uses the drop-and-stop technique to cut the stopped grooves for the sliding doors.
The author holds one of two pieces of wood showing precisely cut grooves in each.
 Achieving precise spacing and depth is critical. The top slots are cut slightly deeper to allow the doors to be lifted to clear the bottom of the case when they are being inserted or removed.
The author uses a knife to mark where two pieces of wood meet.
 Scribing the square end. Cullum dry-fits the vertical divider to ascertain the exact end point of the door tracks. After scribing, he’ll chisel the tracks square.

The glue-up

I do the glue-up in two stages. First I glue all the interior parts and the right side. When they have cured, I add the rest of the carcass and the back. When clamping the sides, it helps to have full-length clamping cauls to help keep everything flat and prevent the unsupported finger joints from drifting inward.

When the glue has cured, I remove the clamps and drill for the pins. Each finger gets two 3⁄16-in.-dia. wooden pegs. While tapered wooden nails are preferable, they can be difficult to find; regular birch dowels will suffice. Taking the whole case to the drill press, I drill pin holes 1-1⁄4 in. deep. I cut the pins 1-1⁄2 in. long and, using a pencil sharpener, chamfer one end.

While it’s tempting to skip this step, it makes the insertion of the pins easier and lessens the risk of damaging the surrounding surface. After using a toothpick to lightly apply glue inside the hole and to the pin, I tap them in. When all are in on one face, I clean off the glue and cut off the excess before moving to the next side. When everything is cured, I plane the pins and the fingers flush.

I make the base next, and when I glue up the mortise-and-tenon joints connecting the four parts of the base, I use the finished case as a pattern. When those joints have cured, I glue and pin the base to the case, leaving several inches on each side of the back corners unglued to accommodate some movement of the case.

The author is gluing pieces together with lots of clamps The author is gluing pieces together with lots of clamps

Assembling the innards. In the first stage of assembly (above, left, and right), Cullum glues up all the interior parts and the right case side.

More of the cabinet is glued up.
Adding the outside. With the cabinet’s interior all glued up, Cullum assembles the finger joints and inserts the back, bringing together the entire case.

A completed tansu carcase with four clamps on it.


-This is the first of three posts for this project. Part 2: Drawers and Doors will be available on Feb 21, and Part 3: Shopmade tansu hardware on Feb 28th. Of course, if you can’t wait, the article PDF is available below, and the digital issue is available to Unlimited members now!

Traditional Tansu, Part 1: The case

Tapered Lamination

Slender curves have the necessary bulk for joinery

 

Traditional Tansu, Part 1: The case

Dovetailed Tea Box

This project offers a variety of techniques in a small package.

 

Traditional Tansu, Part 1: The case

How to build an Andon lamp

This lamp, by Craig Vandall Stevens, features mitered tenons joining the rails to the legs, and Kumiko panels that are made separately and slipped into the lamp’s frame.

 

Download FREE PDF

when you enter your email address below.

View PDF


Source link

Leave a Reply

Your email address will not be published. Required fields are marked *